Difference between revisions of "ToDo"

From Ohio Packet
Jump to: navigation, search
 
(12 intermediate revisions by the same user not shown)
Line 13: Line 13:
  
 
Jameco: <br>
 
Jameco: <br>
−
* 34 Pin polarized connectors: Jameco# 32644 (Qty 20) [Syntech I and XTR trunk mount cable construction]
+
* DB-25 Metalized Plastic Hood: Jameco #25604 (Qty 50) [Packet Polling Cables]<br>
−
* Minifit Jr. 10 conductor receptical housing: Jameco# 880714 (Qty 25) [Mini XTR (8ch) Power Connectors] '''OUT OF STOCK UNTIL 4/2/2013!'''<br>
+
* BC547B NPN Transistor: Jameco #254801 (Qty 100) [LMR Preamplifier Circuits]<br>
−
* Minifit Jr. Female connectors: Jameco# 304733 (Qty 200) [Mini XTR (8ch Power Connectors] <br>
+
* 220uF 16V, Electrolytic, Radial Capacitors: Jameco #198872 (Qty 100) [LMR Preamplifier Circuits]<br>
−
* DB-25 Male Solder Cup Style connectors: Jameco# 223010 (Qty 20) [BPQ Polling Cables]
+
* 470k 1/2w Resistor: Jameco #662151 (Qty 100) [LMR Preamplfier Circuits]<br>
−
* DB-25 Metalized Hoods: Jameco# 25604 (Qty 20) [BPQ Polling Cables]
+
* 1.25x.25" Inline Fuse Holder: Jameco# 108792 (Qty. 50) [LMR Power Cables]<br>
−
* Molex .093" Female Crimp connectors: Jameco #224231 (Qty 300) [Syntech I and XTR Accessory Connector Maintenance]
 
−
* Molex .093" Male Crimp connectors: Jameco# 224223 (Qty 600) [Syntech I and XTR Accessory Connector Maintenance]
 
−
* 9 Pin Molex Male connector .093": Jameco# 224119 (Qty 75) [XTR/Syntech I Power connector]
 
−
* 1.25x.25" 20 Amp Fast Blow Fuses: Jameco# 1769137 (Qty 100) [LMR Power Cables]<br>
 
  
 
* Precidion Voltage Regulator/Linear UA723CN : Jameco# 1129906 (Qty 10) [Astron Rebuilds]<br> (BACKORDERED)
 
* Precidion Voltage Regulator/Linear UA723CN : Jameco# 1129906 (Qty 10) [Astron Rebuilds]<br> (BACKORDERED)
Line 38: Line 34:
 
* Universal Mate-n-Lock 9 pin connectors: Mouser# 571-14806730 (Qty 25) [Syntech I High Power Connectors]
 
* Universal Mate-n-Lock 9 pin connectors: Mouser# 571-14806730 (Qty 25) [Syntech I High Power Connectors]
 
* Minifit Jr. Connector female pins .143": Mouser# 538-39-00-0078 (Qty 200) [Mini XTR (8ch) Power Connectors]
 
* Minifit Jr. Connector female pins .143": Mouser# 538-39-00-0078 (Qty 200) [Mini XTR (8ch) Power Connectors]
 +
* 34 Pin polarized connectors: Mouser # 571-1658621-8  (Qty 30)
  
 
Digikey: <br>
 
Digikey: <br>
 
* 2 Position .140MATE-N-LOK power connector: Digikey# A25469-ND (Qty 20) [XTR High Power Connectors]
 
* 2 Position .140MATE-N-LOK power connector: Digikey# A25469-ND (Qty 20) [XTR High Power Connectors]
 
* .140 In diameter female plugs: Digikey# A25461CT-ND (Qty 60) [XTR High Power Connectors]
 
* .140 In diameter female plugs: Digikey# A25461CT-ND (Qty 60) [XTR High Power Connectors]
−
 
+
* .140 In diameter pin extraction tool: DigiKey# A25474-ND (Qty 1) [XTR/Syntech I High Power Connector Maintenance]
 +
* 9 Pin Molex Male connector .093": Digikey #WM1329-ND Molex #0003092092 or #03-09-2092 [XTR/Syntech I Power connector]
 +
* Connector Housing 8 Position 1.25mm: DigiKey# WM1726-ND (Qty 100) [Kenwood TK Internal Accessory Connector]
 +
* Connector Female 1.25mm 26-28awg: DigiKey# WM1142CT-ND (Qty 800) [Kenwood TK Internal Accessory Connector]
 +
* MicroFit 3.0 Extraction Tool: DigiKey# WM9937-ND (Qty 1) [Kenwood TK Internal Accessory Connector]
 +
* Connector Female 2 Position VL Series: DigiKey# 455-2355-ND (JST Part VLR-02V) (Qty ??) [Kenwood TK-780/880/980/981 Power Connectors (Jack)]
 +
* Connector Pin VL Series Pins 12g: DigiKey# 455-2349-2-ND (JST Part DSVM-81T-P2.0) (Qty ??) [Kenwood TK-780/880/980/981 Power Connectors (Jack Pins)]
 +
* Connector Male 2 Position VL Series: DigiKey# 455-2374-ND (JTS Part VLP-02V) (Qty 50) [Kenwood TK-780/880/980/981 Power Connectors (Plug)]
 +
* Connector Socket VL Series 12g: DigiKey# 455-2377-1-ND (JTS Part SVF-81T-P2.0) (Qty 100) [Kenwood TK-780/880/980/981 Power Connectors (Plug Pins)]
 +
* Connector Male 4 Position VL Series: DigiKey# 455-2351-ND (JTS Part VLP-04V) (Qty 10) [Kenwood TK-690H/790H/890H Power Connectors (Plug)]
 +
* VL Series Extraction Tool: DigiKey# 455-2370-ND (JTS Part VLJ-20) (Qty 1) [Kenwood TK-780/880/980/981 Power Connector Maintenance]
 +
* Tyco Electronics OEM T power connector housing Female: Digikey# A107344-ND (TE Part 172130-1)(Qty 50) [Vertex FTL-n011 Power/Other radio Power Connectors]
 +
* Tyco Electronics OEM T power connector connector Female: Digikey# A111037TR-ND (TE Part 170342-1) (Qty 100) [Vertex FTL-n011 Power/Other radio Power Connectors]
 +
* Tyco Electronics OEM T power connector housing Male: Digikey# A106264-ND (TE Part 172129-1)(Qty 50) [Vertex FTL-n011 Power/Other radio Power Connectors]
 +
* Tyco Electronics OEM T power connector connector Male: Digikey# A100472CT-ND (TE Part 170340-1) (Qty 100) [Vertex FTL-n011 Power/Other radio Power Connectors]
 +
* Connector Housing 11 Position .156 with Ramp: DigiKey# WM2109-ND (Molex part 09-50-3111) (Qty 35) [GE Phoenix Power/Accessory Connectors]
 +
* Connector Housing 8 Position .156 with Ramp: DigiKey# WM2106-ND (Molex part 0009503081) (Qty 53) [GE Phoenix Microphone Connectors]
 +
* Connector Terminator female 18-24awg: DigiKey# WM2300-ND (Molex part 0008500106) (Qty 1100) [GE Phoenix Power/Accessory/Microphone Connectors]
 +
* Molex .156 Connector Extraction Tool: DigiKey# WM9928-ND (Molex part 0011030016) (Qty 1) [GE Phoenix Connector]
 +
* TE Connectivity AMP Connectors: DigiKey# 104422-1-ND (AMP part 104422-1) (Qty 50) [Motorola Radius/Maxtrac 16 pin Accessory Connector]
 +
* Connection Socket for 20-24awg: DigiKey# A3007-ND (AMP part 1-87309-3) (Qty 800) [Motorola Radius/Maxtrac 16 pin Accessory Connector]
 +
* CONN PLUG HOUSING EP .156 5POS: DigiKey# A30504-ND (AMP part 1-1123722-5) (Qty 25) [Motorola Radius/Maxtrac 5 pin Accessory Connector]
 +
* CONN EP CONTACT 18-22AWG TIN: DigiKey# A30499TR-ND (AMP part 1123721-1) (Qty 125) [Motorola Radius/Maxtrac 5 pin Accessory Connector]
  
 
----
 
----
Line 66: Line 85:
 
* Molex .093" & .062" Crimp Tool: Jameco #227491 (Qty 2) [Syntech I and XTR Accessory Connector Maintenance]
 
* Molex .093" & .062" Crimp Tool: Jameco #227491 (Qty 2) [Syntech I and XTR Accessory Connector Maintenance]
 
* Molex .093" Female Crimp connector: Jameco #224231 (Qty 100) [Syntech I and XTR Accessory Connector Maintenance]
 
* Molex .093" Female Crimp connector: Jameco #224231 (Qty 100) [Syntech I and XTR Accessory Connector Maintenance]
−
* 9 Pin Molex Male connector .093": Jameco# 224119 [XTR/Syntech I Power connector]
+
* 9 Pin Molex Male connector .093": Jameco# 224119 [XTR/Syntech I Power connector] '''No longer carried as of 2/1/2017'''
 +
* 34 Pin polarized connectors: Jameco# 32644 (Qty 20) [Syntech I and XTR trunk mount cable construction]
 +
* Minifit Jr. 10 conductor receptical housing: Jameco# 880714 (Qty 25) [Mini XTR (8ch) Power Connectors] '''OUT OF STOCK UNTIL 4/2/2013!'''<br>
 +
* Minifit Jr. Female connectors: Jameco# 304733 (Qty 200) [Mini XTR (8ch Power Connectors] <br>
 +
* DB-25 Male Solder Cup Style connectors: Jameco# 223010 (Qty 20) [BPQ Polling Cables]
 +
* DB-25 Metalized Hoods: Jameco# 25604 (Qty 20) [BPQ Polling Cables]
 +
* Molex .093" Female Crimp connectors: Jameco #224231 (Qty 300) [Syntech I and XTR Accessory Connector Maintenance]
 +
* Molex .093" Male Crimp connectors: Jameco# 224223 (Qty 600) [Syntech I and XTR Accessory Connector Maintenance]
 +
* 9 Pin Molex Male connector .093": Jameco# 224119 (Qty 75) [XTR/Syntech I Power connector]
 +
* 1.25x.25" 20 Amp Fast Blow Fuses: Jameco# 1769137 (Qty 100) [LMR Power Cables]<br>
  
 
----
 
----
  
 
'''Build'''
 
'''Build'''
−
* Construct pieces for Richwood site.  Cabinet is now ready, obtained 5/8" bolts to fill open bulkhead slots.  Planning on using 3 of 8 to start. Diamond V2000, Diamond V23 (APRS), Cushcraft 224WB.  Use 4 (2 low/rear, 2 top) 5" fans for air circulation.
 
−
* Setup a pair of 70-530B radios for 438 MHz range as a dedicated link between CMHSW2 and CMHSW3.  Will use 70cm side of AR-270B at CMHSW2, antenna at CMHSW3 TBD.  Set quality to 250 on both sides.
 
−
* Remove 223.420 MHz radio/antenna from CMHSW2, CMHSW3
 
−
* Add 145.010 MHz radio at CMHSW2, use 2m side of AR-270B.  Attempt path to LAN01 in Lancaster, possibly MECH/CMHSW4.
 
−
* Add 29.275 MHz port to CMHSW2 and CMHSW4.  Try to make a seasonal resilient link to replace 223.420 MHz.  Use VALIDCALLS and L3ONLY in BPQ port definitions
 
−
* Construct 7 element 70cm quad, end mounted for Mechanicsburg to point to Richwood.
 
  
 
'''Develop/Test'''
 
'''Develop/Test'''
−
* What can we do to acquire more gear or funding?
 
  
 
'''Maintenance/Modifications'''
 
'''Maintenance/Modifications'''
Line 86: Line 107:
 
'''Sites'''
 
'''Sites'''
  
−
* Columbus/Battelle - 446.625 Radio seems to be slightly off frequency or is clipping due to over-deviation.  Prepare LMR replacement wired for a DRSI DPK*2.
+
* Ashland - Online
−
 
 
−
* Columbus/Lincoln Tower - Tune VHF Duplexer for 144.390/144.930 to share GP-9 on 2m.  Get inventory of existing antennas.  Should be a 449-6S beam pointed towards Worthington and a 224WB pointed towards Lancaster.
 
  
−
* Columbus/Southwest - RF Path tests:
+
* Columbus/Battelle - Had to be removed due to personel changes at Battelle
−
      145.010 MHz 1200 Baud -> C K8QIK-12 - directional antenna towards Lancaster
 
−
      145.010 MHz 1200 Baud -> C N8XIX-12 - directional antenna towards Lancaster
 
−
      446.625 MHz 1200 Baud -> C KB8UVN-5 / omni or directional antenna north
 
−
      446.625 MHz 1200 Baud -> C KB8UVN-7 / omni or directional antenna north
 
−
      446.625 MHz 1200 Baud -> C W8CQK-1 / omni or directional antenna north
 
−
      446.975 MHz 1200 Baud -> C K8QIK-2 - directional antenna towards Lancaster
 
  
−
* Johnstown - 223.420 MHz port not working at all to CMHSW2/CMHSW3.  Repurpose as a possible link to Richwood.  Run ethernet cable to outbuilding, possibly establish backup AXIP/AXUDP links.  Repurposed 446.625 MHz port to 446.975 MHz and have a solid link into LANSW1/Lancaster.
+
* Columbus/Lincoln Tower - Parking for now
  
−
* Lancaster/Firestation #1 - Radio, TNCs, Eproms (TheNet X-1J4) and Diplexer installed. LAN01:K8QIK-12 on 145.010 MHz, #LANU1:K8QIK-14 on 440.500 MHz.  UHF link is working well to WW Hill.  Link to MECH only functional in evening, going to try increasing transmit power, need 20amp power supply.
+
* Johnstown - Online, replaced computer with 1U compaq server, seems to hold up in heat better.
  
−
* Lancaster/FMC - Radio, TNCs, computer are ready.  Waiting to install V2000 and A270-6S.  Will sunset BBS at LFARC Clubhouse afterwards.
+
* Lancaster/Firestation #1 - Online
  
−
* Lancaster/WW Hill - Everything is on the air, continued problem with 223.660 TNC.  TNC swapped out, issues persist, CON LED goes solid and stops passing traffic. Suspect either BPQKISS channel D eprom or polling cable (7 port).  Prepare replacement of both for next trip.
+
* Lancaster/FMC - Online, installed Polyphaser on V2000, grounded packet and echolink computers.
  
−
* Pataskala - Contact W8ALC to see if he has interest in hosting additional systems.
+
* Lancaster/WW Hill - Online, installed Polyphaser on V2000
  
−
* Mechanicsburg - Add additional 70cm antenna to allow links to Richwood.  Need additional Radio and TNC.  Probably use 222 MHz to link to Mutual.  Will need to add 2 more ports to the BPQ polling cable (5 total).
+
* Mechanicsburg - Offline, cronic computer trouble.  Have replacement to Rick.  Waiting installation.  Need to install small antenna in 433 MHz range to link Mechanicsburg to Mutual
  
−
* Mutual - V2000 is in the air, 2m and 70cm radios available, nothing tentative yet.
+
* Mutual - Offline, wiring issue, waiting to hear from Rick.
  
−
* Richwood - 2 of 3 antennas are installed, feedlines run.  Need to install one additional mast to support last 2m antenna (F23) for APRS.  Cabinet is finished. Radios, TNCs and computer is ready.  Going to need help getting the cabinet up there.
+
* Richwood - Online
  
−
* South Vienna - Site inventory, see available antenna space, what bands are available for linking.  Hoping this will open up a path to Dayton.
+
* Springfield - Online
  
−
* Springfield - Antenna space unavailable at this time.  Need to relocate IRA VHF repeater first.  Tentatively planning on a 70cm link to South Vienna and Mechanicsburg.
+
* West Liberty - On hold
  
−
* Worthington/CMHSW2 - Attempting additional 70cm link to CMHSW3.  Isolation seems ok, problems on CMHSW3 side.
+
* Worthington/CMHSW2 - Online, recently added 3.585 USB WINMOR port.  Ideally want to install end fed half wave for 30m and 80m to help reduce crosstalk.
  
−
* Worthington/CMHSW3 - Getting significant bleeding between 440.100 and 438.500 ports.  Need to try different antenna locations, possibly going cross polarized or try to move the frequency down further.
+
* Worthington/CMHSW3 - Offline, hopefully pending move
  
−
* Upper Sandusky - Get in contact with station engineer.  See what facilities are available.  Reach out to local club to see if any sponsorship can be gained (Mainly antennas, feedline and power supplies).  Ideally would like to link to Richwood, possibly Mechanicsburg to the south then Findlay and Tiffin to the north.
+
* Upper Sandusky - On hold, Richwood side is now online.  Get in contact with station engineer.  See what facilities are available.  Reach out to local club to see if any sponsorship can be gained (Mainly antennas, feedline and power supplies).  Ideally would like to link to Richwood, possibly Mechanicsburg to the south then Findlay and Tiffin to the north.

Latest revision as of 14:30, 15 April 2018

Here is a list of things we are collectively working on.

Purchase

  • Acquire/split up power supplies at CMHSW2, CMHSW3, CMHSW4, #RCHWD to handle higher load from Midland LMR Radios
  • Acquire large spool (1000ft) of RG-213 and PL-259 Connectors. ***Update 11/08/09*** Secured 3 500ft rolls of LMR400 clone cable. 1st roll is consumed post MECH install.
  • Continue to acquire gear/test equipment for shared workshop. Will need antennas to cover as much HF as possible, 6m, 2m, 222 MHz, 70cm. Spare power supplies, few computers for workstations/web search, eprom burning facilities, packet host to test cables for 4 main interfaces: soundmodem(Linux), DRSI, TNC2, Kantronics 9 pin.
  • Locate portable computer, 20amp switching power supply and appropriate cabling for a portable LMR programming station covering both Syntech I and XTR/Syntech II models.
  • Syntech I programmer. Ordered on 5/5, expected ship on 5/7. ***Update 6/02/09*** Programmer arrived, successfully programming Z-273 and Z-383 modules.
  • Diamond MX-2000 (6m/2m/70cm) Triplexers with pigtails to allow connections to LMR radios.
  • SWR Meter effective up to 1200 MHz for usage for 33cm and 23cm antenna construction. (Diamond SX-1100) ***Update 1/26/10*** Meter purchased

Component orders:

Jameco:

  • DB-25 Metalized Plastic Hood: Jameco #25604 (Qty 50) [Packet Polling Cables]
  • BC547B NPN Transistor: Jameco #254801 (Qty 100) [LMR Preamplifier Circuits]
  • 220uF 16V, Electrolytic, Radial Capacitors: Jameco #198872 (Qty 100) [LMR Preamplifier Circuits]
  • 470k 1/2w Resistor: Jameco #662151 (Qty 100) [LMR Preamplfier Circuits]
  • 1.25x.25" Inline Fuse Holder: Jameco# 108792 (Qty. 50) [LMR Power Cables]
  • Precidion Voltage Regulator/Linear UA723CN : Jameco# 1129906 (Qty 10) [Astron Rebuilds]
    (BACKORDERED)

Mouser:

  • Minifit Jr. 10 conductor receptical housing: Mouser# 538-39-01-2105 (Qty 25)


  • 500 pF Ceramic Disc Capacitor: Mouser# 562R10TST50 (Qty 10) - equal number to UA723CN Regulators [Astron Rebuilds]
  • Bipolar Transistor 2N3771: Mouser# 511-2N3771 (Qty 40) - Replacements for Astron Power Supplies [Astron Rebuilds]
  • .093 Molex Pin Extractor: Mouser# 538-11-03-0006 (Qty 2) [LMR Power Cables]
  • 3v Lithium Battery for MFJ-1270b/c, 1274, 1289: Mouser# 639-CR2430-P22 (Qty 10) [TNC Maintenance]
  • Audio Bridge Amplifier TDA7240A: Mouser# 511-TDA7240AH (Qty 5) [XTR Maintenence/Repair]
  • .140 In diameter pin plugs: Mouser# 571-350391-1 (Qty 100) [Syntech I High Power Connectors]
  • Universal Mate-n-Lock 9 pin connectors: Mouser# 571-14806730 (Qty 25) [Syntech I High Power Connectors]
  • Minifit Jr. Connector female pins .143": Mouser# 538-39-00-0078 (Qty 200) [Mini XTR (8ch) Power Connectors]
  • 34 Pin polarized connectors: Mouser # 571-1658621-8 (Qty 30)

Digikey:

  • 2 Position .140MATE-N-LOK power connector: Digikey# A25469-ND (Qty 20) [XTR High Power Connectors]
  • .140 In diameter female plugs: Digikey# A25461CT-ND (Qty 60) [XTR High Power Connectors]
  • .140 In diameter pin extraction tool: DigiKey# A25474-ND (Qty 1) [XTR/Syntech I High Power Connector Maintenance]
  • 9 Pin Molex Male connector .093": Digikey #WM1329-ND Molex #0003092092 or #03-09-2092 [XTR/Syntech I Power connector]
  • Connector Housing 8 Position 1.25mm: DigiKey# WM1726-ND (Qty 100) [Kenwood TK Internal Accessory Connector]
  • Connector Female 1.25mm 26-28awg: DigiKey# WM1142CT-ND (Qty 800) [Kenwood TK Internal Accessory Connector]
  • MicroFit 3.0 Extraction Tool: DigiKey# WM9937-ND (Qty 1) [Kenwood TK Internal Accessory Connector]
  • Connector Female 2 Position VL Series: DigiKey# 455-2355-ND (JST Part VLR-02V) (Qty ??) [Kenwood TK-780/880/980/981 Power Connectors (Jack)]
  • Connector Pin VL Series Pins 12g: DigiKey# 455-2349-2-ND (JST Part DSVM-81T-P2.0) (Qty ??) [Kenwood TK-780/880/980/981 Power Connectors (Jack Pins)]
  • Connector Male 2 Position VL Series: DigiKey# 455-2374-ND (JTS Part VLP-02V) (Qty 50) [Kenwood TK-780/880/980/981 Power Connectors (Plug)]
  • Connector Socket VL Series 12g: DigiKey# 455-2377-1-ND (JTS Part SVF-81T-P2.0) (Qty 100) [Kenwood TK-780/880/980/981 Power Connectors (Plug Pins)]
  • Connector Male 4 Position VL Series: DigiKey# 455-2351-ND (JTS Part VLP-04V) (Qty 10) [Kenwood TK-690H/790H/890H Power Connectors (Plug)]
  • VL Series Extraction Tool: DigiKey# 455-2370-ND (JTS Part VLJ-20) (Qty 1) [Kenwood TK-780/880/980/981 Power Connector Maintenance]
  • Tyco Electronics OEM T power connector housing Female: Digikey# A107344-ND (TE Part 172130-1)(Qty 50) [Vertex FTL-n011 Power/Other radio Power Connectors]
  • Tyco Electronics OEM T power connector connector Female: Digikey# A111037TR-ND (TE Part 170342-1) (Qty 100) [Vertex FTL-n011 Power/Other radio Power Connectors]
  • Tyco Electronics OEM T power connector housing Male: Digikey# A106264-ND (TE Part 172129-1)(Qty 50) [Vertex FTL-n011 Power/Other radio Power Connectors]
  • Tyco Electronics OEM T power connector connector Male: Digikey# A100472CT-ND (TE Part 170340-1) (Qty 100) [Vertex FTL-n011 Power/Other radio Power Connectors]
  • Connector Housing 11 Position .156 with Ramp: DigiKey# WM2109-ND (Molex part 09-50-3111) (Qty 35) [GE Phoenix Power/Accessory Connectors]
  • Connector Housing 8 Position .156 with Ramp: DigiKey# WM2106-ND (Molex part 0009503081) (Qty 53) [GE Phoenix Microphone Connectors]
  • Connector Terminator female 18-24awg: DigiKey# WM2300-ND (Molex part 0008500106) (Qty 1100) [GE Phoenix Power/Accessory/Microphone Connectors]
  • Molex .156 Connector Extraction Tool: DigiKey# WM9928-ND (Molex part 0011030016) (Qty 1) [GE Phoenix Connector]
  • TE Connectivity AMP Connectors: DigiKey# 104422-1-ND (AMP part 104422-1) (Qty 50) [Motorola Radius/Maxtrac 16 pin Accessory Connector]
  • Connection Socket for 20-24awg: DigiKey# A3007-ND (AMP part 1-87309-3) (Qty 800) [Motorola Radius/Maxtrac 16 pin Accessory Connector]
  • CONN PLUG HOUSING EP .156 5POS: DigiKey# A30504-ND (AMP part 1-1123722-5) (Qty 25) [Motorola Radius/Maxtrac 5 pin Accessory Connector]
  • CONN EP CONTACT 18-22AWG TIN: DigiKey# A30499TR-ND (AMP part 1123721-1) (Qty 125) [Motorola Radius/Maxtrac 5 pin Accessory Connector]

Reference:

Jameco:

  • 1.25x.25" Inline Fuse Holder: Jameco# 108792 (Qty. 50) [LMR Power Cables]
  • 1.25x.25" Fast Blow Fuses: Jameco# 1769170 (Qty 100) [LMR Power Cables]
  • Minifit Jr. 10 conductor receptical housing: Jameco# 880714 (Qty 40) [Mini XTR (8ch) Power Connectors]
  • 34 Pin connector crimp tool: Jameco# 73252 (Qty 1) [Syntech I and XTR trunk mount cable construction]
  • 34 Pin polarized connectors: Jameco# 32644 (Qty 20) [Syntech I and XTR trunk mount cable construction]
  • 34 Pin gray ribbon cable - 100ft: Jameco# 644050 (Qty 1) [Syntech I and XTR trunk mount cable construction]
  • 12 Pin Molex Accessory Connectors (.062"): Jameco# 224549 (Qty 20) [XTR High Power/Syntech II Accessory Connectors]
  • .062" Male Pins: Jameco# 224565 (Qty 100) [XTR High Power/Syntech II Accessory Connectors]
  • .062" Pin Extractor: Jameco# 142156 (Qty 2) [XTR High Power/Syntech Accessory Connector Maintenance]
  • DB-25 Male Connector: Jameco #38789 (Qty 50) [Packet Polling Cables]
  • DB-25 Metalized Plastic Hood: Jameco #25604 (Qty 50) [Packet Polling Cables]
  • DB-9 Female Connector: Jameco #15771 (Qty 10) [SVXLink Interface Cables]
  • Digital Multimeter, Fluke-115: Jameco #1537328 (Qty 1) [General Use]
  • Connector Accessories Mini-Fit JR Extraction Tool: Jameco #1961541 (Qty 1) [Mini XTR (8ch) Power Connector Maintenance]
  • Molex .093" & .062" Crimp Tool: Jameco #227491 (Qty 2) [Syntech I and XTR Accessory Connector Maintenance]
  • Molex .093" Female Crimp connector: Jameco #224231 (Qty 100) [Syntech I and XTR Accessory Connector Maintenance]
  • 9 Pin Molex Male connector .093": Jameco# 224119 [XTR/Syntech I Power connector] No longer carried as of 2/1/2017
  • 34 Pin polarized connectors: Jameco# 32644 (Qty 20) [Syntech I and XTR trunk mount cable construction]
  • Minifit Jr. 10 conductor receptical housing: Jameco# 880714 (Qty 25) [Mini XTR (8ch) Power Connectors] OUT OF STOCK UNTIL 4/2/2013!
  • Minifit Jr. Female connectors: Jameco# 304733 (Qty 200) [Mini XTR (8ch Power Connectors]
  • DB-25 Male Solder Cup Style connectors: Jameco# 223010 (Qty 20) [BPQ Polling Cables]
  • DB-25 Metalized Hoods: Jameco# 25604 (Qty 20) [BPQ Polling Cables]
  • Molex .093" Female Crimp connectors: Jameco #224231 (Qty 300) [Syntech I and XTR Accessory Connector Maintenance]
  • Molex .093" Male Crimp connectors: Jameco# 224223 (Qty 600) [Syntech I and XTR Accessory Connector Maintenance]
  • 9 Pin Molex Male connector .093": Jameco# 224119 (Qty 75) [XTR/Syntech I Power connector]
  • 1.25x.25" 20 Amp Fast Blow Fuses: Jameco# 1769137 (Qty 100) [LMR Power Cables]

Build

Develop/Test

Maintenance/Modifications

  • Inventory existing radio and TNC stock. Once inventoried, modify to ham bands. Mark each radio with center frequency and maximum power output. 7/08/10 Radios and TNCs inventory completed, begin modifications/tuning next.

Sites

  • Ashland - Online
  • Columbus/Battelle - Had to be removed due to personel changes at Battelle
  • Columbus/Lincoln Tower - Parking for now
  • Johnstown - Online, replaced computer with 1U compaq server, seems to hold up in heat better.
  • Lancaster/Firestation #1 - Online
  • Lancaster/FMC - Online, installed Polyphaser on V2000, grounded packet and echolink computers.
  • Lancaster/WW Hill - Online, installed Polyphaser on V2000
  • Mechanicsburg - Offline, cronic computer trouble. Have replacement to Rick. Waiting installation. Need to install small antenna in 433 MHz range to link Mechanicsburg to Mutual
  • Mutual - Offline, wiring issue, waiting to hear from Rick.
  • Richwood - Online
  • Springfield - Online
  • West Liberty - On hold
  • Worthington/CMHSW2 - Online, recently added 3.585 USB WINMOR port. Ideally want to install end fed half wave for 30m and 80m to help reduce crosstalk.
  • Worthington/CMHSW3 - Offline, hopefully pending move
  • Upper Sandusky - On hold, Richwood side is now online. Get in contact with station engineer. See what facilities are available. Reach out to local club to see if any sponsorship can be gained (Mainly antennas, feedline and power supplies). Ideally would like to link to Richwood, possibly Mechanicsburg to the south then Findlay and Tiffin to the north.
Retrieved from "https://ohiopacket.org/index.php?title=ToDo&oldid=2221"