Search results

Create the page "$1" on this wiki! See also the search results found.

• Pickaway
  '''Nodecall:''' XX8YY-1<br>
  423 bytes (65 words) - 23:51, 4 January 2019
• Ross
  This system hosts CHLBBS:W8BAP-1 BBS system and CHLQSO:W8BAP-6 Chat system
  572 bytes (93 words) - 18:29, 28 August 2021
• Stark
  '''Nodecall:''' XX8YY-1<br>
  420 bytes (65 words) - 23:56, 4 January 2019
• Summit
  '''Nodecall:''' XX8YY-1<br>
  421 bytes (65 words) - 00:00, 5 January 2019
• Washington
  '''Nodecall:''' W8HH-1<br> ...5.690 MHz. This system hosts WORGRM:W8ORG-10 RMS Gateway and WORGBB:W8ORG-1 BBS<br>
  2 KB (214 words) - 12:24, 27 November 2022
• ToDo
  ...age for 33cm and 23cm antenna construction. (Diamond SX-1100) '''***Update 1/26/10***''' Meter purchased * 470k 1/2w Resistor: Jameco #662151 (Qty 100) [LMR Preamplfier Circuits]<br>
  10 KB (1,377 words) - 15:30, 15 April 2018
• Calculating Net/Rom route quality
  NODEA:KB8UVN-1 '''NODEA:KB8UVN-1} Nodes:'''<br>
  7 KB (1,284 words) - 07:45, 17 December 2011
• Replacing JNOS with Linux
  ...s on the interface. We've used the AMPRNet address. We will use 44.128.0.1 for this example.<br> ifconfig <interfacename> 44.128.0.1 netmask 255.255.255.255
  7 KB (1,170 words) - 21:51, 20 March 2013
• Setting Up Winlink RMS Packet and Direwolf
  1) Before you can run a Winlink RMS station, you must request authorization t
  3 KB (448 words) - 15:38, 9 December 2018
• Lake
  '''Nodecall:''' XX8YY-1<br>
  419 bytes (65 words) - 12:19, 22 August 2007
• Building a 4 Port Packet Controller
  1) It is assumed there is a working Raspberry Pi 3 B+ with Raspian/Raspberry 1) 1x 24x12 hole perf board<br>
  45 KB (7,789 words) - 15:48, 25 October 2022
• Modifying Kenwood TK-760(H)G/762(H)G/860(H)G/862(H)G/863G for Packet Service
  <table valign="TOP" border="1"> <td align="left">1 = 148-174 MHz, 2 = 136-162 MHz</td>
  38 KB (6,498 words) - 18:20, 4 July 2021
• 4 Port Controller Administration Guide
  1) Log in as the "pi" user<br> ...nt of the controller with the USB ports on the left, left to right is port 1, 2, 3 and 4<br>
  7 KB (1,168 words) - 21:15, 26 June 2021
• Modifying Kenwood TK-760(H)/762(H)/860(H)/862(H) for Packet Service
  <table valign="TOP" border="1"> <td align="left">1 = 148-174 MHz, 2 = 136-156 MHz</td>
  33 KB (5,650 words) - 21:03, 28 June 2021
• Modifying Dell PowerEdge 1950/2950 Power Supplies for Amateur Service
  1) Face the power supply with pins facing forward. We want to place jumpers ...measure output. This may vary some but should fall somewhere near the 12.1-12.4VDC range.
  11 KB (1,748 words) - 12:17, 13 November 2022

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)